hallo,

ich habe jetzt die platine vom fabqu bekommen, angeschlossen, das ergebnis verstehe ich in zweierlei punkten nicht:

Code:
Terminal cleared!

[RP6BOOT]

[READY]


RP6Control Multi IO Selftest 1!

Writing 128 to EEPROM address 5:
Done!

Reading EEPROM address 5:

I2C ERROR --> TWI STATE IS: 0x20

I2C ERROR --> TWI STATE IS: 0x48
Done!
EEPROM address 5 content: 17

3V3 Voltage:  2.6V
ADC 3V3: 532
TOUCHED!!!
ADC Touch: 537
Temperature:  23.4°
RTC: 12:00:00  10.01.2013
Temperature:  20.8°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.3V
ADC 3V3: 472
NOT touched.
ADC Touch: 423
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  21.8°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.2V
ADC 3V3: 448
NOT touched.
ADC Touch: 392
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  22.1°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 439
NOT touched.
ADC Touch: 382
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  23.7°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 437
NOT touched.
ADC Touch: 381
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  23.0°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 436
NOT touched.
ADC Touch: 380
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  21.2°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 435
NOT touched.
ADC Touch: 379
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  22.6°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 435
NOT touched.
ADC Touch: 379
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  22.8°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 435
NOT touched.
ADC Touch: 379
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  21.3°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 435
NOT touched.
ADC Touch: 379
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  21.8°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 436
NOT touched.
ADC Touch: 380
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  22.1°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 435
NOT touched.
ADC Touch: 379
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  21.4°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 435
NOT touched.
ADC Touch: 379
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  22.1°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 435
NOT touched.
ADC Touch: 379
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  23.4°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 435
NOT touched.
ADC Touch: 379
Temperature:  23.3°
RTC: 12:00:00  10.01.2013
Temperature:  22.6°
BAT Current:    0.0mA
BAT Voltage:  7.4V
SERVO Volt.:  5.0V
VCC Voltage:  5.1V

3V3 Voltage:  2.1V
ADC 3V3: 435
NOT touched.
ADC Touch: 379
Temperature:  23.3°
RTC: 12:00:00  10.01.2013

[RP6BOOT]

[READY]
das verhalten der 3.3 V - sinkt von 2,6 auch 2,1V

das nichtreagieren des berührungssensors, auch beim berühren nicht (antennen wie auch beuteil direkt reagieren nicht)


Fabqu hat gemeint ich soll den ausdruck ins forum stellen, evtl. ein softwareproblem?