Hallo
Meine Platine ist inzwischen auch angekommen, nochmals herzlichen Dank dafür an alle die dazu beigetragen haben.
Ich bin jetzt voll neidisch auf eure Erfolge, weil ich es mal wieder nicht hinbekomme. Wie alle anderen auch stürze ich mich zuerst auf die WIFI-Funktion, aber das will einfach nicht funktionieren. Grundsätzlich wird das Board erkannt, nach "Factory Settings", "Initial WIFI Config (9600 Baud)" und "Configure WIFI Module!" blinkt die grüne LED langsam und alleine und das Log sieht so aus:
Mit "Device Discover" wird das Board nun mit 192.168.137.2:2000 zum Adden angeboten. Allerdings enden alle Versuche zu connecten mit einem Timeout. Die Selbstkonfiguration endet nach 47% ebenfalls mit einem Timeout und folgender Ausgabe:Code:WLAN Module perform factory reset. ### DELAY ### DELAY factory RESET ### DELAY ### DELAY ### DELAY reboot Set Comport... Baudrate is set to: 38400 OK! Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... Delay... Delay... WIFI issue command: factory RESET Delay... Delay... Delay... WIFI issue command: reboot ### WIFI configure commands DONE! Set Comport... Baudrate is set to: 38400 OK! Baudrate is set to: 38400 Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Reset WIFI and activate passthrough mode with 9600 Baud! ### Run WIFI configure script:config/wifi_init_config_baudrate.txt Script:1:CMD: ver Script:2:DELAY Delay... Script:3:CMD: ver OK! Script:5:CMD: show rssi Script:6:CMD: get mac Script:7:CMD: set wlan join 0 OK! Script:9:CMD: get everything Script:10:DELAY Delay... Script:11:DELAY Delay... Script:12:DELAY Delay... Script:13:DELAY Delay... Script:14:DELAY Delay... Script:15:DELAY Delay... Script:16:CMD: set sys mask 0x21f0 OK! Script:18:CMD: set sys value 0x0 OK! Script:20:CMD: set UART raw 500000 OK! Script:22:CMD: set UART flow 0 OK! Script:24:CMD: set wlan linkmon 5 OK! Script:26:CMD: set wlan rate 8 OK! Script:28:CMD: set comm size 1024 OK! Script:30:CMD: set comm time 10 OK! Script:32:CMD: set comm remote 0 OK! Script:34:CMD: set opt deviceid RP6v2-M256-WIFI OK! Script:36:DELAY Delay... Script:37:CMD: save Script:38:DELAY Delay... Script:39:DELAY Delay... Script:40:DELAY Delay... Script:41:CMD: reboot Script:42:DELAY Delay... Script:43:DELAY Delay... ### WIFI configure script DONE! set wlan ssid RP6-WIFI-AP ### WAIT_FOR:AOK set ip dhcp 0 ### WAIT_FOR:AOK set ip netmask 255.255.255.0 ### WAIT_FOR:AOK set ip adr 192.168.137.2 ### WAIT_FOR:AOK set ip gateway 192.168.137.1 ### WAIT_FOR:AOK set dns address 192.168.137.1 ### WAIT_FOR:AOK set wlan join 1 ### WAIT_FOR:AOK set wlan channel 0 ### WAIT_FOR:AOK set wlan auth 3 ### WAIT_FOR:AOK ### DELAY set wlan passphrase radbruch2012 ### WAIT_FOR:AOK ### DELAY ### DELAY set wlan hide 1 ### WAIT_FOR:AOK set opt deviceid RP6-WIFI ### WAIT_FOR:AOK ### DELAY save ### DELAY ### DELAY reboot Set Comport... Baudrate is set to: 38400 OK! Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... WIFI issue command: set wlan ssid RP6-WIFI-AP OK! WIFI issue command: set ip dhcp 0 OK! WIFI issue command: set ip netmask 255.255.255.0 OK! WIFI issue command: set ip adr 192.168.137.2 OK! WIFI issue command: set ip gateway 192.168.137.1 OK! WIFI issue command: set dns address 192.168.137.1 OK! WIFI issue command: set wlan join 1 OK! WIFI issue command: set wlan channel 0 OK! WIFI issue command: set wlan auth 3 OK! Delay... WIFI issue command: set wlan passphrase radbruch2012 OK! Delay... Delay... WIFI issue command: set wlan hide 1 OK! WIFI issue command: set opt deviceid RP6-WIFI OK! Delay... WIFI issue command: save Delay... Delay... WIFI issue command: reboot ### WIFI configure commands DONE! Got UDP Broadcast on port 55555 from IP: 192.168.137.2; open port:2000 Accespoint MAC:00:0c:f6:6d:2b:61; ch:1; rssi:46; rtc_val:8 Ver: WiFly Ver 2.32, 02-13-2012 ; ID:RP6-WIFI BatVolt:
Was nun?Code:Seltest Settings: IP Subnet:192.168.137. Use fixed IP:192.168.137.2 HOME Mode, accept any RSSI level! Do NOT update Firmware! RSSI Threshold is set to: -46dBm #################################################################### #################################################################### Complete Factory initial configure has been started! PLEASE WAIT until it finishes... #################################################################### #################################################################### Set Comport... Baudrate is set to: 38400 OK! Baudrate is set to: 38400 Configure Bootloader Settings... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Get current Boot settings! Configure Boot settings! Reset to defaults! Store new settings! Loader Action: FINISHED! Loader Action: CONFIGURE DONE! Run Factory RESET... WLAN Module perform factory reset if required... Set Comport... Baudrate is set to: 38400 OK! ### DELAY ### DELAY factory RESET ### DELAY ### DELAY ### DELAY reboot Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... Loader Action: FINISHED! Delay... Delay... WIFI issue command: factory RESET Delay... Delay... Delay... WIFI issue command: reboot ### WIFI configure commands DONE! Loader Action: CONFIGURE DONE! Run Initial Configure... Set Comport... Baudrate is set to: 38400 OK! Baudrate is set to: 38400 Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Reset WIFI and activate passthrough mode with 9600 Baud! ### Run WIFI configure script:config/wifi_init_config_baudrate.txt Loader Action: FINISHED! Script:1:CMD: ver Script:2:DELAY Delay... Script:3:CMD: ver OK! Script:5:CMD: show rssi Script:6:CMD: get mac Script:7:CMD: set wlan join 0 OK! Script:9:CMD: get everything Script:10:DELAY Delay... Script:11:DELAY Delay... Script:12:DELAY Delay... Script:13:DELAY Delay... Script:14:DELAY Delay... Script:15:DELAY Delay... Script:16:CMD: set sys mask 0x21f0 OK! Script:18:CMD: set sys value 0x0 OK! Script:20:CMD: set UART raw 500000 OK! Script:22:CMD: set UART flow 0 OK! Script:24:CMD: set wlan linkmon 5 OK! Script:26:CMD: set wlan rate 8 OK! Script:28:CMD: set comm size 1024 OK! Script:30:CMD: set comm time 10 OK! Script:32:CMD: set comm remote 0 OK! Script:34:CMD: set opt deviceid RP6v2-M256-WIFI OK! Script:36:DELAY Delay... Script:37:CMD: save Script:38:DELAY Delay... Script:39:DELAY Delay... Script:40:DELAY Delay... Script:41:CMD: reboot Script:42:DELAY Delay... Script:43:DELAY Delay... ### WIFI configure script DONE! Loader Action: CONFIGURE DONE! Get Infos and Configure... Set Comport... Baudrate is set to: 38400 OK! Activate WIFI Passthrough + Reset WIFI Module + Get Infos... Baudrate is set to: 38400 Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Reset WIFI, activate passthrough mode and get Infos! ### Get WIFI Module Infos... Loader Action: FINISHED! GOT VER = WiFly Ver 2.32, 02-13-2012 on RN-171 6 GOT MAC = Mac Addr=00:06:66:72:03:4c 52 GOT RSSI = RSSI=(-4) dBm < 92 ### Get WIFI Module Infos... DONE! Loader Action: GET WLAN INFOS DONE! Same MAC, no IP Change required. Continue... MAC: 00:06:66:72:03:4c Set Comport... Baudrate is set to: 38400 OK! ### Parse WIFI configure script:config/wifi_defaults_basic.txt ### WIFI configure script DONE! Set Comport... Baudrate is set to: 38400 OK! Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... Loader Action: FINISHED! WIFI issue command: WIFI issue command: WIFI issue command: ver OK! WIFI issue command: show rssi WIFI issue command: get mac WIFI issue command: set wlan join 0 OK! Delay... Delay... WIFI issue command: set sys mask 0x21f0 OK! WIFI issue command: set sys value 0x0 OK! WIFI issue command: set ip dhcp 0 OK! WIFI issue command: set ip flags 0x6 OK! WIFI issue command: set ip gateway 192.168.10.1 OK! WIFI issue command: set wlan join 1 OK! WIFI issue command: set wlan linkmon 5 OK! WIFI issue command: set wlan rate 8 OK! WIFI issue command: set comm size 1024 OK! WIFI issue command: set comm time 10 OK! WIFI issue command: set comm remote 0 OK! WIFI issue command: set opt deviceid RP6v2-M256-WIFI OK! WIFI issue command: set ftp address 208.109.14.133 OK! Delay... WIFI issue command: set wlan ssid M256TST OK! WIFI issue command: set ip netmask 255.255.255.0 OK! WIFI issue command: set ip adr 192.168.137.2 OK! Delay... WIFI issue command: set wlan auth 3 OK! WIFI issue command: set wlan passphrase radbruch2012 OK! WIFI issue command: set wlan hide 1 OK! Delay... WIFI issue command: set UART raw 500000 OK! WIFI issue command: set UART flow 1 OK! Delay... WIFI issue command: save Delay... Delay... Delay... WIFI issue command: reboot Delay... Delay... ### WIFI configure commands DONE! Loader Action: CONFIGURE DONE! Test WLAN Reset... Set Comport... Baudrate is set to: 38400 OK! Activate WIFI Passthrough + Reset WIFI Module... Baudrate is set to: 38400 Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Reset WIFI and activate passthrough mode! Loader Action: FINISHED! OK got normal response from Module after Reset! WLAN configure for test... Set Comport... Baudrate is set to: 38400 OK! ### DELAY set ip adr 192.168.137.2 ### WAIT_FOR:AOK save ### DELAY ### DELAY ### DELAY reboot ### DELAY ### DELAY Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... Loader Action: FINISHED! Delay... WIFI issue command: set ip adr 192.168.137.2 WAIT RESPONSE_TIMEOUT!!!! Issue Command wait for response "AOK" FAILURE, script aborted! Loader Action: CONFIGURE FAILED! ########## Test Configure failed... Retry # 0 to get infos and configure... Set Comport... Baudrate is set to: 38400 OK! ### DELAY set ip adr 192.168.137.2 ### WAIT_FOR:AOK save ### DELAY ### DELAY ### DELAY reboot ### DELAY ### DELAY Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... Loader Action: FINISHED! Delay... WIFI issue command: set ip adr 192.168.137.2 OK! WIFI issue command: save Delay... Delay... Delay... WIFI issue command: reboot Delay... Delay... ### WIFI configure commands DONE! Loader Action: CONFIGURE DONE! Test WLAN connection, please wait... Open Network Connection... #### Network close all... #### Network close all done! #### BEGIN CONNECT TO: 192.168.137.2:2000 Connection open FAILED! Please try again! Retry # 1... ############ Will now retry with different IP... Set Comport... Baudrate is set to: 38400 OK! ### DELAY set ip adr 192.168.137.2 ### WAIT_FOR:AOK save ### DELAY ### DELAY ### DELAY reboot ### DELAY ### DELAY Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... Loader Action: FINISHED! Delay... #### Network close all... #### Network close all done! Network Connection Status changed: CONNECT TIME OUT! #### DISCONNECTED Network Connection Status changed: DISCONNECTED! WIFI issue command: set ip adr 192.168.137.2 OK! WIFI issue command: save Delay... Delay... Delay... WIFI issue command: reboot Delay... Delay... ### WIFI configure commands DONE! Loader Action: CONFIGURE DONE! Test WLAN connection, please wait... Open Network Connection... #### Network close all... #### Network close all done! #### BEGIN CONNECT TO: 192.168.137.2:2000 Connection open FAILED! Please try again! Retry # 2... ############ Will now retry with different IP... Set Comport... Baudrate is set to: 38400 OK! ### DELAY set ip adr 192.168.137.2 ### WAIT_FOR:AOK save ### DELAY ### DELAY ### DELAY reboot ### DELAY ### DELAY Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... Loader Action: FINISHED! Delay... #### Network close all... #### Network close all done! Network Connection Status changed: CONNECT TIME OUT! #### DISCONNECTED Network Connection Status changed: DISCONNECTED! WIFI issue command: set ip adr 192.168.137.2 OK! WIFI issue command: save Delay... Delay... Delay... WIFI issue command: reboot Delay... Delay... ### WIFI configure commands DONE! Loader Action: CONFIGURE DONE! Test WLAN connection, please wait... Open Network Connection... #### Network close all... #### Network close all done! #### BEGIN CONNECT TO: 192.168.137.2:2000 Connection open FAILED! Please try again! Retry # 3... ############ Will now retry with different IP... Set Comport... Baudrate is set to: 38400 OK! ### DELAY set ip adr 192.168.137.2 ### WAIT_FOR:AOK save ### DELAY ### DELAY ### DELAY reboot ### DELAY ### DELAY Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... Loader Action: FINISHED! Delay... #### Network close all... #### Network close all done! Network Connection Status changed: CONNECT TIME OUT! #### DISCONNECTED Network Connection Status changed: DISCONNECTED! WIFI issue command: set ip adr 192.168.137.2 OK! WIFI issue command: save Delay... Delay... Delay... WIFI issue command: reboot Delay... Delay... ### WIFI configure commands DONE! Loader Action: CONFIGURE DONE! Test WLAN connection, please wait... Open Network Connection... #### Network close all... #### Network close all done! #### BEGIN CONNECT TO: 192.168.137.2:2000 Connection open FAILED! Please try again! Retry # 4... ############ Will now retry with different IP... Set Comport... Baudrate is set to: 38400 OK! ### DELAY set ip adr 192.168.137.2 ### WAIT_FOR:AOK save ### DELAY ### DELAY ### DELAY reboot ### DELAY ### DELAY Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... Loader Action: FINISHED! Delay... WIFI issue command: set ip adr 192.168.137.2 OK! WIFI issue command: save #### Network close all... #### Network close all done! Network Connection Status changed: CONNECT TIME OUT! #### DISCONNECTED Network Connection Status changed: DISCONNECTED! Delay... Delay... Delay... WIFI issue command: reboot Delay... Delay... ### WIFI configure commands DONE! Loader Action: CONFIGURE DONE! Test WLAN connection, please wait... Open Network Connection... #### Network close all... #### Network close all done! #### BEGIN CONNECT TO: 192.168.137.2:2000 Connection open FAILED! Please try again! ############ Network Connection failed due to connection error / timeout! Abort. Please retry manually. If this fails, check settings and assembly! Network Connection Timeout ERROR (101) ||| Network Connection attempt timed out! #### Network close all... #### Network close all done! Network Connection Status changed: CONNECT TIME OUT! #### DISCONNECTED Network Connection Status changed: DISCONNECTED!
Gruß
mic
[Edit]
Wie kommt das denn rein:
WIFI issue command: set wlan ssid M256TST
In den Einstellungen für die Autoconfig-Funktion hatte ich meine eigene SSID "RP6-WIFI-AP" eingetragen. Ein weiterer Test mit "M256TST" als SSID wird allerdings schon nach 11% mit der Meldung
### WIFI configure script config/wifi_defaults_flow_FACTORY.txt NOT FOUND!!!
abgebrochen:
Code:Seltest Settings: IP Subnet:192.168.137. Use fixed IP:192.168.137.2 Factory Mode! Do NOT update Firmware! RSSI Threshold is set to: -46dBm #################################################################### #################################################################### Complete Factory initial configure has been started! PLEASE WAIT until it finishes... #################################################################### #################################################################### Set Comport... Baudrate is set to: 38400 OK! Baudrate is set to: 38400 Configure Bootloader Settings... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Get current Boot settings! Configure Boot settings! Reset to defaults! Store new settings! Loader Action: FINISHED! Loader Action: CONFIGURE DONE! Run Factory RESET... WLAN Module perform factory reset if required... Set Comport... Baudrate is set to: 38400 OK! ### DELAY ### DELAY factory RESET ### DELAY ### DELAY ### DELAY reboot Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure commands... Loader Action: FINISHED! Delay... Delay... WIFI issue command: factory RESET Delay... Delay... Delay... WIFI issue command: reboot ### WIFI configure commands DONE! Loader Action: CONFIGURE DONE! Run Initial Configure... Set Comport... Baudrate is set to: 38400 OK! Baudrate is set to: 38400 Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Reset WIFI and activate passthrough mode with 9600 Baud! ### Run WIFI configure script:config/wifi_init_config_baudrate.txt Loader Action: FINISHED! Script:1:CMD: ver Script:2:DELAY Delay... Script:3:CMD: ver OK! Script:5:CMD: show rssi Script:6:CMD: get mac Script:7:CMD: set wlan join 0 OK! Script:9:CMD: get everything Script:10:DELAY Delay... Script:11:DELAY Delay... Script:12:DELAY Delay... Script:13:DELAY Delay... Script:14:DELAY Delay... Script:15:DELAY Delay... Script:16:CMD: set sys mask 0x21f0 OK! Script:18:CMD: set sys value 0x0 OK! Script:20:CMD: set UART raw 500000 OK! Script:22:CMD: set UART flow 0 OK! Script:24:CMD: set wlan linkmon 5 OK! Script:26:CMD: set wlan rate 8 OK! Script:28:CMD: set comm size 1024 OK! Script:30:CMD: set comm time 10 OK! Script:32:CMD: set comm remote 0 OK! Script:34:CMD: set opt deviceid RP6v2-M256-WIFI OK! Script:36:DELAY Delay... Script:37:CMD: save Script:38:DELAY Delay... Script:39:DELAY Delay... Script:40:DELAY Delay... Script:41:CMD: reboot Script:42:DELAY Delay... Script:43:DELAY Delay... ### WIFI configure script DONE! Loader Action: CONFIGURE DONE! Get Infos and Configure... Set Comport... Baudrate is set to: 38400 OK! Activate WIFI Passthrough + Reset WIFI Module + Get Infos... Baudrate is set to: 38400 Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Reset WIFI, activate passthrough mode and get Infos! ### Get WIFI Module Infos... Loader Action: FINISHED! GOT VER = WiFly Ver 2.32, 02-13-2012 on RN-171 6 GOT MAC = Mac Addr=00:06:66:72:03:4c 52 GOT RSSI = RSSI=(-4) dBm < 92 ### Get WIFI Module Infos... DONE! Loader Action: GET WLAN INFOS DONE! Same MAC, no IP Change required. Continue... MAC: 00:06:66:72:03:4c Set Comport... Baudrate is set to: 38400 OK! Baudrate is set to: 38400 Configure WIFI... Connected to [WIFI] target! Target ID received: RP6: Board ID 8, Firmware Version 1.4, Board Rev.: 3 ["RP6 M256 WIFI", 8, MEGA2560, 0, 253952, true] Configure WIFI passthrough mode! ### Run WIFI configure script:config/wifi_defaults_flow_FACTORY.txt ### WIFI configure script config/wifi_defaults_flow_FACTORY.txt NOT FOUND!!! Loader Action: FINISHED!Code:D:\_rp6-wifi\RobotLoader_20120717\RobotLoader_20120717\config>dir Volume in Laufwerk D: hat keine Bezeichnung. Volumeseriennummer: DA78-31FF Verzeichnis von D:\_rp6-wifi\RobotLoader_20120717\RobotLoader_20120717\config 17.07.2012 21:10 <DIR> . 17.07.2012 21:10 <DIR> .. 17.07.2012 21:10 2.055 boards.cfg 19.07.2012 19:17 247 files.cfg 19.07.2012 19:17 247 files_net.cfg 17.07.2012 21:10 <DIR> ftp_home 20.07.2012 17:53 324 rn171.properties 19.07.2012 19:17 848 rp6loader.cfg 17.07.2012 21:10 <DIR> selftest 20.07.2012 19:07 677 wifi.cfg 17.07.2012 21:10 1.036 wifi_defaults.txt 17.07.2012 21:10 626 wifi_defaults_basic.txt 17.07.2012 21:10 606 wifi_init_config.txt 17.07.2012 21:10 644 wifi_init_config_baudrate.txt 17.07.2012 21:10 606 wifi_init_config_flow.txt 11 Datei(en), 7.916 Bytes 4 Verzeichnis(se), 815.963.852.800 Bytes frei
Zitieren
Lesezeichen