1. Was sucht irgendwelche Pfadangabe hier:
# List C source files here. (C dependencies are automatically generated.)
SRC = $(TARGET).c C:/Dokumente und Einstellungen/Thomas Grübler/Eigene Dateien/Roboter und Physik/Projekt PuckCollect/Erste C-versuche/taster und led.c
nach SRC = $(TARGET).c kommt nichts mehr hin.

2. Versuch es mal hiermit:
Code:
MCU = atmega8

#Tagret einstellen
TARGET = netzteil
#Sourcefiles
SRC = $(TARGET).c

SRC += 

FORMAT = ihex

#Assemblerfiles
ASRC=

OPT = s

#Compilerflags
CFLAGS = -g -O$(OPT) \
	-funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums \
	-Wall -Wstrict-prototypes \
	-Wa,-ahlms=$(<:.c=.lst)

#Assemblerflags
ASFLAGS = -Wa,-ahlms=$(<:.S=.lst),-gstabs

#Linkerflags

LDFLAGS = -Wl,-Map=$(TARGET).map,--cref

# Additional libraries
#
# Minimalistic printf version
#LDFLAGS += -Wl,-u,vfprintf -lprintf_min
#
# Floating point printf version (requires -lm below)
#LDFLAGS +=  -Wl,-u,vfprintf -lprintf_flt
#
# -lm = math library
LDFLAGS += -lm

# Define programs and commands.
SHELL = sh

CC = avr-gcc

OBJCOPY = avr-objcopy
OBJDUMP = avr-objdump
SIZE = avr-size

REMOVE = rm -f
COPY = cp

HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
ELFSIZE = $(SIZE) -A $(TARGET).elf

FINISH = echo Errors: none
BEGIN = echo -------- begin --------
END = echo --------  end  --------




# Define all object files.
OBJ = $(SRC:.c=.o) $(ASRC:.S=.o) 

# Define all listing files.
LST = $(ASRC:.S=.lst) $(SRC:.c=.lst)

# Combine all necessary flags and optional flags.
# Add target processor to flags.
ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)



# Default target.
all: begin gccversion sizebefore $(TARGET).elf $(TARGET).hex $(TARGET).eep \
	$(TARGET).lss sizeafter finished end


# Eye candy.
# AVR Studio 3.x does not check make's exit code but relies on
# the following magic strings to be generated by the compile job.
begin:
	@$(BEGIN)

finished:
	@$(FINISH)

end:
	@$(END)


# Display size of file.
sizebefore:
	@if [ -f $(TARGET).elf ]; then echo Size before:; $(ELFSIZE);fi

sizeafter:
	@if [ -f $(TARGET).elf ]; then echo Size after:; $(ELFSIZE);fi



# Display compiler version information.
gccversion : 
	$(CC) --version




# Convert ELF to COFF for use in debugging / simulating in
# AVR Studio or VMLAB.
COFFCONVERT=$(OBJCOPY) --debugging \
	--change-section-address .data-0x800000 \
	--change-section-address .bss-0x800000 \
	--change-section-address .noinit-0x800000 \
	--change-section-address .eeprom-0x810000 


coff: $(TARGET).elf
	$(COFFCONVERT) -O coff-avr $< $(TARGET).cof


extcoff: $(TARGET).elf
	$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof

# Create final output files (.hex, .eep) from ELF output file.
%.hex: %.elf
	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@

%.eep: %.elf
	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@

# Create extended listing file from ELF output file.
%.lss: %.elf
	$(OBJDUMP) -h -S $< > $@



# Link: create ELF output file from object files.
.SECONDARY : $(TARGET).elf
.PRECIOUS : $(OBJ)
%.elf: $(OBJ)
	$(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS)


# Compile: create object files from C source files.
%.o : %.c
	$(CC) -c $(ALL_CFLAGS) $< -o $@


# Compile: create assembler files from C source files.
%.s : %.c
	$(CC) -S $(ALL_CFLAGS) $< -o $@


# Assemble: create object files from assembler source files.
%.o : %.S
	$(CC) -c $(ALL_ASFLAGS) $< -o $@






# Target: clean project.
clean: begin clean_list finished end

clean_list :
	$(REMOVE) $(TARGET).hex
	$(REMOVE) $(TARGET).eep
	$(REMOVE) $(TARGET).obj
	$(REMOVE) $(TARGET).cof
	$(REMOVE) $(TARGET).elf
	$(REMOVE) $(TARGET).map
	$(REMOVE) $(TARGET).obj
	$(REMOVE) $(TARGET).a90
	$(REMOVE) $(TARGET).sym
	$(REMOVE) $(TARGET).lnk
	$(REMOVE) $(TARGET).lss
	$(REMOVE) $(OBJ)
	$(REMOVE) $(LST)
	$(REMOVE) $(SRC:.c=.s)
	$(REMOVE) $(SRC:.c=.d)


# Automatically generate C source code dependencies. 
# (Code originally taken from the GNU make user manual and modified 
# (See README.txt Credits).)
#
# Note that this will work with sh (bash) and sed that is shipped with WinAVR
# (see the SHELL variable defined above).
# This may not work with other shells or other seds.
#
%.d: %.c
	set -e; $(CC) -MM $(ALL_CFLAGS) $< \
	| sed 's,\(.*\)\.o[ :]*,\1.o \1.d : ,g' > $@; \
	[ -s $@ ] || rm -f $@


# Remove the '-' if you want to see the dependency files generated.
-include $(SRC:.c=.d)



# Listing of phony targets.
.PHONY : all begin finish end sizebefore sizeafter gccversion coff extcoff \
	clean clean_list program




#
MCU und TARGET anpassen und fertig.

3.
Aber ich weiß noch immer nichts wie ich die Ports mit zb 00011100 als Hex angebe.
Hast Du keinen Taschenrechner?
Am sonsten als Übung ein kleines Programm dafür schreiben.

Gruß Sebastian