datatom
08.04.2010, 17:56
Hallo,
ich habe das Problem, dass ich mit HTerm 0.8.1 beta keine Daten von meinem Controller empfangen kann.
Folgendes Programm von ATMEL AVR32-UC3-SoftwareFramework-1.6.0 ist auf dem Controller installiert (Laut Beschreibung am Anfang des Programms, sollen empfangene Daten zurück gesendet werden):
/* This source file is part of the ATMEL AVR32-UC3-SoftwareFramework-1.6.0 Release */
/*This file is prepared for Doxygen automatic documentation generation.*/
/*! \file ************************************************** *******************
*
* \brief USART example application for AVR32 USART driver.
*
* - Compiler: IAR EWAVR32 and GNU GCC for AVR32
* - Supported devices: All AVR32 devices with a USART module can be used.
* - AppNote:
*
* \author Atmel Corporation: http://www.atmel.com \n
* Support and FAQ: http://support.atmel.no/
*
************************************************** ****************************/
/*! \page License
* Copyright (c) 2009 Atmel Corporation. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice, this
* list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* 3. The name of Atmel may not be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* 4. This software may only be redistributed and used in connection with an Atmel
* AVR product.
*
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE
*
*/
/*! \mainpage
* \section intro Introduction
* This is the documentation for the data structures, functions, variables,
* defines, enums, and typedefs for the USART software driver.\n It also comes
* bundled with an example. This example is a basic Hello-World example.\n
* Example's operating mode:
* -# A message is displayed on the PC terminal ("Hello, this is AT32UC3 saying hello! (press enter)")
* -# You may then type any character other than CR(Carriage Return) and it will
* be echoed back to the PC terminal.
* -# If you type a CR, "'CRLF'Goodbye." is echoed back to the PC terminal and
* the application ends.
*
* \section files Main Files
* - usart.c: USART driver;
* - usart.h: USART driver header file;
* - usart_example.c: USART example application.
*
* \section compilinfo Compilation Information
* This software is written for GNU GCC for AVR32 and for IAR Embedded Workbench
* for Atmel AVR32. Other compilers may or may not work.
*
* \section deviceinfo Device Information
* All AVR32 devices with a USART module can be used.
*
* \section configinfo Configuration Information
* This example has been tested with the following configuration:
* - EVK1100, EVK1101, UC3C_EK, EVK1104, EVK1105 evaluation kits; STK600+RCUC3L routing card; AT32UC3L-EK
* - CPU clock:
* -- 12 MHz : EVK1100, EVK1101, EVK1104, EVK1105, AT32UC3L-EK evaluation kits; STK600+RCUC3L routing card
* -- 16 Mhz : AT32UC3C-EK
* - USART1 (on EVK1100 or EVK1101) connected to a PC serial port via a standard
* RS232 DB9 cable, or USART0 (on EVK1105) or USART2 (on AT32UC3C-EK) or USART1 (on EVK1104)
* or USART3 (on AT32UC3L-EK) abstracted with a USB CDC connection to a PC;
* STK600 usart port for the STK600+RCUC3L setup (connect STK600.PE2 to STK600.RS232 SPARE.TXD
* and STK600.PE3 to STK600.RS232 SPARE.RXD)
* - PC terminal settings:
* - 57600 bps,
* - 8 data bits,
* - no parity bit,
* - 1 stop bit,
* - no flow control.
*
* \section contactinfo Contact Information
* For further information, visit
* Atmel AVR32 (http://www.atmel.com/products/AVR32/).\n
* Support and FAQ: http://support.atmel.no/
*/
#include <avr32/io.h>
#include "compiler.h"
#include "board.h"
#include "power_clocks_lib.h"
#include "gpio.h"
#include "usart.h"
/*! \name USART Settings
*/
//! @{
# define EXAMPLE_TARGET_PBACLK_FREQ_HZ FOSC0 // PBA clock target frequency, in Hz
#if BOARD == EVK1100
# define EXAMPLE_USART (&AVR32_USART1)
# define EXAMPLE_USART_RX_PIN AVR32_USART1_RXD_0_0_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART1_RXD_0_0_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART1_TXD_0_0_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART1_TXD_0_0_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART1_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#elif BOARD == EVK1101
# define EXAMPLE_USART (&AVR32_USART1)
# define EXAMPLE_USART_RX_PIN AVR32_USART1_RXD_0_0_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART1_RXD_0_0_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART1_TXD_0_0_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART1_TXD_0_0_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART1_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#elif BOARD == UC3C_EK
# define EXAMPLE_USART (&AVR32_USART2)
# define EXAMPLE_USART_RX_PIN AVR32_USART2_RXD_0_1_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART2_RXD_0_1_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART2_TXD_0_1_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART2_TXD_0_1_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART2_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBB
#elif BOARD == EVK1104
# define EXAMPLE_USART (&AVR32_USART1)
# define EXAMPLE_USART_RX_PIN AVR32_USART1_RXD_0_0_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART1_RXD_0_0_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART1_TXD_0_0_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART1_TXD_0_0_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART1_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#elif BOARD == EVK1105
# define EXAMPLE_USART (&AVR32_USART0)
# define EXAMPLE_USART_RX_PIN AVR32_USART0_RXD_0_0_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART0_RXD_0_0_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART0_TXD_0_0_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART0_TXD_0_0_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART0_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#elif BOARD == STK600_RCUC3L0
# define EXAMPLE_USART (&AVR32_USART1)
# define EXAMPLE_USART_RX_PIN AVR32_USART1_RXD_0_1_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART1_RXD_0_1_FUNCTION
// For the RX pin, connect STK600.PORTE.PE3 to STK600.RS232 SPARE.RXD
# define EXAMPLE_USART_TX_PIN AVR32_USART1_TXD_0_1_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART1_TXD_0_1_FUNCTION
// For the TX pin, connect STK600.PORTE.PE2 to STK600.RS232 SPARE.TXD
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART1_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#elif BOARD == UC3L_EK
# define EXAMPLE_USART (&AVR32_USART3)
# define EXAMPLE_USART_RX_PIN AVR32_USART3_RXD_0_0_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART3_RXD_0_0_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART3_TXD_0_0_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART3_TXD_0_0_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART3_CLK_PBA
# define EXAMPLE_TARGET_DFLL_FREQ_HZ 96000000 // DFLL target frequency, in Hz
# define EXAMPLE_TARGET_MCUCLK_FREQ_HZ 12000000 // MCU clock target frequency, in Hz
# undef EXAMPLE_TARGET_PBACLK_FREQ_HZ
# define EXAMPLE_TARGET_PBACLK_FREQ_HZ 12000000 // PBA clock target frequency, in Hz
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#endif
#if !defined(EXAMPLE_USART) || \
!defined(EXAMPLE_USART_RX_PIN) || \
!defined(EXAMPLE_USART_RX_FUNCTION) || \
!defined(EXAMPLE_USART_TX_PIN) || \
!defined(EXAMPLE_USART_TX_FUNCTION)
# error The USART configuration to use in this example is missing.
#endif
//! @}
#if BOARD == UC3L_EK
/*! \name Parameters to pcl_configure_clocks().
*/
//! @{
static scif_gclk_opt_t gc_dfllif_ref_opt = { SCIF_GCCTRL_SLOWCLOCK, 0, OFF };
static pcl_freq_param_t pcl_dfll_freq_param =
{
.main_clk_src = PCL_MC_DFLL0,
.cpu_f = EXAMPLE_TARGET_MCUCLK_FREQ_HZ,
.pba_f = EXAMPLE_TARGET_PBACLK_FREQ_HZ,
.pbb_f = EXAMPLE_TARGET_PBACLK_FREQ_HZ,
.dfll_f = EXAMPLE_TARGET_DFLL_FREQ_HZ,
.pextra_params = &gc_dfllif_ref_opt
};
//! @}
#endif
/*! \brief This is an example demonstrating the USART RS232 TX and RX
* functionalities using the USART driver.
*/
int main(void)
{
static const gpio_map_t USART_GPIO_MAP =
{
{EXAMPLE_USART_RX_PIN, EXAMPLE_USART_RX_FUNCTION},
{EXAMPLE_USART_TX_PIN, EXAMPLE_USART_TX_FUNCTION}
};
// USART options.
static const usart_options_t USART_OPTIONS =
{
.baudrate = 57600,
.charlength = 8,
.paritytype = USART_NO_PARITY,
.stopbits = USART_1_STOPBIT,
.channelmode = USART_NORMAL_CHMODE
};
#if BOARD == UC3L_EK
// Note: on the AT32UC3L-EK board, there is no crystal/external clock connected
// to the OSC0 pinout XIN0/XOUT0. We shall then program the DFLL and switch the
// main clock source to the DFLL.
pcl_configure_clocks(&pcl_dfll_freq_param);
// Note: since it is dynamically computing the appropriate field values of the
// configuration registers from the parameters structure, this function is not
// optimal in terms of code size. For a code size optimal solution, it is better
// to create a new function from pcl_configure_clocks_dfll0() and modify it
// to use preprocessor computation from pre-defined target frequencies.
#else
// Configure Osc0 in crystal mode (i.e. use of an external crystal source, with
// frequency FOSC0) with an appropriate startup time then switch the main clock
// source to Osc0.
pcl_switch_to_osc(PCL_OSC0, FOSC0, OSC0_STARTUP);
#endif
// Assign GPIO to USART.
gpio_enable_module(USART_GPIO_MAP,
sizeof(USART_GPIO_MAP) / sizeof(USART_GPIO_MAP[0]));
// Initialize USART in RS232 mode.
usart_init_rs232(EXAMPLE_USART, &USART_OPTIONS, EXAMPLE_TARGET_PBACLK_FREQ_HZ);
// Hello world!
usart_write_line(EXAMPLE_USART, "Hello, this is AT32UC3 saying hello! (press enter)\n");
// Press enter to continue.
while (usart_get_echo_line(EXAMPLE_USART) == USART_FAILURE); // Get and echo characters until end of line.
usart_write_line(EXAMPLE_USART, "Goodbye.\n");
//*** Sleep mode
// This program won't be doing anything else from now on, so it might as well
// sleep.
// Modules communicating with external circuits should normally be disabled
// before entering a sleep mode that will stop the module operation.
// Make sure the USART dumps the last message completely before turning it off.
while(!usart_tx_empty(EXAMPLE_USART));
pcl_disable_module(EXAMPLE_USART_CLOCK_MASK);
// Since we're going into a sleep mode deeper than IDLE, all HSB masters must
// be stopped before entering the sleep mode.
pcl_disable_module(EXAMPLE_PDCA_CLOCK_HSB);
pcl_disable_module(EXAMPLE_PDCA_CLOCK_PB);
// If there is a chance that any PB write operations are incomplete, the CPU
// should perform a read operation from any register on the PB bus before
// executing the sleep instruction.
AVR32_INTC.ipr[0]; // Dummy read
// Go to STATIC sleep mode.
SLEEP(AVR32_PM_SMODE_STATIC);
while (TRUE);
}
Ich habe folgendes Board: http://alvidi.de/avr32_modul_bmb.html
Das Board ist mit einem USB-Adapter (Hersteller: ATEN Model: UC-232A) am PC angeschlossen. Das LED am Adapter blinkt während des Sendens.
Zum Senden und Empfangen habe ich am Board die PIN´s 232IN0 und 232OUT0 angeschlossen und GND_1.
Das Board wird mit 12 V betrieben. PIN´s GND_2 und 5-12V.
Der PIN 232IN0 hat in Warteposition -6,29 V und beim Senden mit HTerm -6,12 V.
Der PIN 232OUT0 hat die ganze Zeit -4,88 V.
Leider weiß ich nicht wie ich das Problem lösen soll und hoffe auf eure Unterstützung.
Vielen Dank.
Grüße
datatom
ich habe das Problem, dass ich mit HTerm 0.8.1 beta keine Daten von meinem Controller empfangen kann.
Folgendes Programm von ATMEL AVR32-UC3-SoftwareFramework-1.6.0 ist auf dem Controller installiert (Laut Beschreibung am Anfang des Programms, sollen empfangene Daten zurück gesendet werden):
/* This source file is part of the ATMEL AVR32-UC3-SoftwareFramework-1.6.0 Release */
/*This file is prepared for Doxygen automatic documentation generation.*/
/*! \file ************************************************** *******************
*
* \brief USART example application for AVR32 USART driver.
*
* - Compiler: IAR EWAVR32 and GNU GCC for AVR32
* - Supported devices: All AVR32 devices with a USART module can be used.
* - AppNote:
*
* \author Atmel Corporation: http://www.atmel.com \n
* Support and FAQ: http://support.atmel.no/
*
************************************************** ****************************/
/*! \page License
* Copyright (c) 2009 Atmel Corporation. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice, this
* list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* 3. The name of Atmel may not be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* 4. This software may only be redistributed and used in connection with an Atmel
* AVR product.
*
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE
*
*/
/*! \mainpage
* \section intro Introduction
* This is the documentation for the data structures, functions, variables,
* defines, enums, and typedefs for the USART software driver.\n It also comes
* bundled with an example. This example is a basic Hello-World example.\n
* Example's operating mode:
* -# A message is displayed on the PC terminal ("Hello, this is AT32UC3 saying hello! (press enter)")
* -# You may then type any character other than CR(Carriage Return) and it will
* be echoed back to the PC terminal.
* -# If you type a CR, "'CRLF'Goodbye." is echoed back to the PC terminal and
* the application ends.
*
* \section files Main Files
* - usart.c: USART driver;
* - usart.h: USART driver header file;
* - usart_example.c: USART example application.
*
* \section compilinfo Compilation Information
* This software is written for GNU GCC for AVR32 and for IAR Embedded Workbench
* for Atmel AVR32. Other compilers may or may not work.
*
* \section deviceinfo Device Information
* All AVR32 devices with a USART module can be used.
*
* \section configinfo Configuration Information
* This example has been tested with the following configuration:
* - EVK1100, EVK1101, UC3C_EK, EVK1104, EVK1105 evaluation kits; STK600+RCUC3L routing card; AT32UC3L-EK
* - CPU clock:
* -- 12 MHz : EVK1100, EVK1101, EVK1104, EVK1105, AT32UC3L-EK evaluation kits; STK600+RCUC3L routing card
* -- 16 Mhz : AT32UC3C-EK
* - USART1 (on EVK1100 or EVK1101) connected to a PC serial port via a standard
* RS232 DB9 cable, or USART0 (on EVK1105) or USART2 (on AT32UC3C-EK) or USART1 (on EVK1104)
* or USART3 (on AT32UC3L-EK) abstracted with a USB CDC connection to a PC;
* STK600 usart port for the STK600+RCUC3L setup (connect STK600.PE2 to STK600.RS232 SPARE.TXD
* and STK600.PE3 to STK600.RS232 SPARE.RXD)
* - PC terminal settings:
* - 57600 bps,
* - 8 data bits,
* - no parity bit,
* - 1 stop bit,
* - no flow control.
*
* \section contactinfo Contact Information
* For further information, visit
* Atmel AVR32 (http://www.atmel.com/products/AVR32/).\n
* Support and FAQ: http://support.atmel.no/
*/
#include <avr32/io.h>
#include "compiler.h"
#include "board.h"
#include "power_clocks_lib.h"
#include "gpio.h"
#include "usart.h"
/*! \name USART Settings
*/
//! @{
# define EXAMPLE_TARGET_PBACLK_FREQ_HZ FOSC0 // PBA clock target frequency, in Hz
#if BOARD == EVK1100
# define EXAMPLE_USART (&AVR32_USART1)
# define EXAMPLE_USART_RX_PIN AVR32_USART1_RXD_0_0_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART1_RXD_0_0_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART1_TXD_0_0_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART1_TXD_0_0_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART1_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#elif BOARD == EVK1101
# define EXAMPLE_USART (&AVR32_USART1)
# define EXAMPLE_USART_RX_PIN AVR32_USART1_RXD_0_0_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART1_RXD_0_0_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART1_TXD_0_0_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART1_TXD_0_0_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART1_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#elif BOARD == UC3C_EK
# define EXAMPLE_USART (&AVR32_USART2)
# define EXAMPLE_USART_RX_PIN AVR32_USART2_RXD_0_1_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART2_RXD_0_1_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART2_TXD_0_1_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART2_TXD_0_1_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART2_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBB
#elif BOARD == EVK1104
# define EXAMPLE_USART (&AVR32_USART1)
# define EXAMPLE_USART_RX_PIN AVR32_USART1_RXD_0_0_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART1_RXD_0_0_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART1_TXD_0_0_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART1_TXD_0_0_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART1_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#elif BOARD == EVK1105
# define EXAMPLE_USART (&AVR32_USART0)
# define EXAMPLE_USART_RX_PIN AVR32_USART0_RXD_0_0_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART0_RXD_0_0_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART0_TXD_0_0_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART0_TXD_0_0_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART0_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#elif BOARD == STK600_RCUC3L0
# define EXAMPLE_USART (&AVR32_USART1)
# define EXAMPLE_USART_RX_PIN AVR32_USART1_RXD_0_1_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART1_RXD_0_1_FUNCTION
// For the RX pin, connect STK600.PORTE.PE3 to STK600.RS232 SPARE.RXD
# define EXAMPLE_USART_TX_PIN AVR32_USART1_TXD_0_1_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART1_TXD_0_1_FUNCTION
// For the TX pin, connect STK600.PORTE.PE2 to STK600.RS232 SPARE.TXD
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART1_CLK_PBA
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#elif BOARD == UC3L_EK
# define EXAMPLE_USART (&AVR32_USART3)
# define EXAMPLE_USART_RX_PIN AVR32_USART3_RXD_0_0_PIN
# define EXAMPLE_USART_RX_FUNCTION AVR32_USART3_RXD_0_0_FUNCTION
# define EXAMPLE_USART_TX_PIN AVR32_USART3_TXD_0_0_PIN
# define EXAMPLE_USART_TX_FUNCTION AVR32_USART3_TXD_0_0_FUNCTION
# define EXAMPLE_USART_CLOCK_MASK AVR32_USART3_CLK_PBA
# define EXAMPLE_TARGET_DFLL_FREQ_HZ 96000000 // DFLL target frequency, in Hz
# define EXAMPLE_TARGET_MCUCLK_FREQ_HZ 12000000 // MCU clock target frequency, in Hz
# undef EXAMPLE_TARGET_PBACLK_FREQ_HZ
# define EXAMPLE_TARGET_PBACLK_FREQ_HZ 12000000 // PBA clock target frequency, in Hz
# define EXAMPLE_PDCA_CLOCK_HSB AVR32_PDCA_CLK_HSB
# define EXAMPLE_PDCA_CLOCK_PB AVR32_PDCA_CLK_PBA
#endif
#if !defined(EXAMPLE_USART) || \
!defined(EXAMPLE_USART_RX_PIN) || \
!defined(EXAMPLE_USART_RX_FUNCTION) || \
!defined(EXAMPLE_USART_TX_PIN) || \
!defined(EXAMPLE_USART_TX_FUNCTION)
# error The USART configuration to use in this example is missing.
#endif
//! @}
#if BOARD == UC3L_EK
/*! \name Parameters to pcl_configure_clocks().
*/
//! @{
static scif_gclk_opt_t gc_dfllif_ref_opt = { SCIF_GCCTRL_SLOWCLOCK, 0, OFF };
static pcl_freq_param_t pcl_dfll_freq_param =
{
.main_clk_src = PCL_MC_DFLL0,
.cpu_f = EXAMPLE_TARGET_MCUCLK_FREQ_HZ,
.pba_f = EXAMPLE_TARGET_PBACLK_FREQ_HZ,
.pbb_f = EXAMPLE_TARGET_PBACLK_FREQ_HZ,
.dfll_f = EXAMPLE_TARGET_DFLL_FREQ_HZ,
.pextra_params = &gc_dfllif_ref_opt
};
//! @}
#endif
/*! \brief This is an example demonstrating the USART RS232 TX and RX
* functionalities using the USART driver.
*/
int main(void)
{
static const gpio_map_t USART_GPIO_MAP =
{
{EXAMPLE_USART_RX_PIN, EXAMPLE_USART_RX_FUNCTION},
{EXAMPLE_USART_TX_PIN, EXAMPLE_USART_TX_FUNCTION}
};
// USART options.
static const usart_options_t USART_OPTIONS =
{
.baudrate = 57600,
.charlength = 8,
.paritytype = USART_NO_PARITY,
.stopbits = USART_1_STOPBIT,
.channelmode = USART_NORMAL_CHMODE
};
#if BOARD == UC3L_EK
// Note: on the AT32UC3L-EK board, there is no crystal/external clock connected
// to the OSC0 pinout XIN0/XOUT0. We shall then program the DFLL and switch the
// main clock source to the DFLL.
pcl_configure_clocks(&pcl_dfll_freq_param);
// Note: since it is dynamically computing the appropriate field values of the
// configuration registers from the parameters structure, this function is not
// optimal in terms of code size. For a code size optimal solution, it is better
// to create a new function from pcl_configure_clocks_dfll0() and modify it
// to use preprocessor computation from pre-defined target frequencies.
#else
// Configure Osc0 in crystal mode (i.e. use of an external crystal source, with
// frequency FOSC0) with an appropriate startup time then switch the main clock
// source to Osc0.
pcl_switch_to_osc(PCL_OSC0, FOSC0, OSC0_STARTUP);
#endif
// Assign GPIO to USART.
gpio_enable_module(USART_GPIO_MAP,
sizeof(USART_GPIO_MAP) / sizeof(USART_GPIO_MAP[0]));
// Initialize USART in RS232 mode.
usart_init_rs232(EXAMPLE_USART, &USART_OPTIONS, EXAMPLE_TARGET_PBACLK_FREQ_HZ);
// Hello world!
usart_write_line(EXAMPLE_USART, "Hello, this is AT32UC3 saying hello! (press enter)\n");
// Press enter to continue.
while (usart_get_echo_line(EXAMPLE_USART) == USART_FAILURE); // Get and echo characters until end of line.
usart_write_line(EXAMPLE_USART, "Goodbye.\n");
//*** Sleep mode
// This program won't be doing anything else from now on, so it might as well
// sleep.
// Modules communicating with external circuits should normally be disabled
// before entering a sleep mode that will stop the module operation.
// Make sure the USART dumps the last message completely before turning it off.
while(!usart_tx_empty(EXAMPLE_USART));
pcl_disable_module(EXAMPLE_USART_CLOCK_MASK);
// Since we're going into a sleep mode deeper than IDLE, all HSB masters must
// be stopped before entering the sleep mode.
pcl_disable_module(EXAMPLE_PDCA_CLOCK_HSB);
pcl_disable_module(EXAMPLE_PDCA_CLOCK_PB);
// If there is a chance that any PB write operations are incomplete, the CPU
// should perform a read operation from any register on the PB bus before
// executing the sleep instruction.
AVR32_INTC.ipr[0]; // Dummy read
// Go to STATIC sleep mode.
SLEEP(AVR32_PM_SMODE_STATIC);
while (TRUE);
}
Ich habe folgendes Board: http://alvidi.de/avr32_modul_bmb.html
Das Board ist mit einem USB-Adapter (Hersteller: ATEN Model: UC-232A) am PC angeschlossen. Das LED am Adapter blinkt während des Sendens.
Zum Senden und Empfangen habe ich am Board die PIN´s 232IN0 und 232OUT0 angeschlossen und GND_1.
Das Board wird mit 12 V betrieben. PIN´s GND_2 und 5-12V.
Der PIN 232IN0 hat in Warteposition -6,29 V und beim Senden mit HTerm -6,12 V.
Der PIN 232OUT0 hat die ganze Zeit -4,88 V.
Leider weiß ich nicht wie ich das Problem lösen soll und hoffe auf eure Unterstützung.
Vielen Dank.
Grüße
datatom