C:\Programme\Atmel\AVR Tools\AvrDragon\AVRDragon.exe" -d ATmega8 -e -mi -pf -if %1
pause
Welche bedeuungen haben dabei die optionen?
Hallo maikatze!
Führe das Programm "AVRDragon.exe" mit dem Kommandozeilenparameter "-h" aus. (z.B. so: "AVRDragon.exe -h"). Dann bekommst du eine Erklärung der Kommandozeilenparameter ausgegeben.
Das sieht dann so aus:
Usage: avrdragon.exe [commands] [options]
Commands:
-h, -? Print this help.
-he Print exit codes.
-e Erase device.
-f <fusebytes> Write high/low fuse bytes. The LSB of fusebytes will be
written to the low fuse byte, and the MSB will be written
to the high fuse byte.
-j <ID> Read JTAG ID string. If an optional ID is specified, the
program will terminate if the read ID differs.
-l <lockbyte> Set the lock byte to the specified value.
-p[f|e|b] Program FLASH (-pf), EEPROM (-pe) or both (-pb) memories.
Requires input files specified with the -if (FLASH)
and/or -ie (EEPROM) options.
-q Read fuse bytes. If the selected device has extended fuse,
it will be also be read.
-r[f|e|b] Read FLASH (-rf), EEPROM (-re) or both (-rb) memories.
Requires output files specified with the -of (FLASH) and/or
-oe (EEPROM) options.
-s Read signature bytes.
-v[f|e|b] Verify FLASH (-vf), EEPROM (-ve) or both (vb) memories.
Requires input files specified with the -if (FLASH) and/or
-ie (EEPROM) options.
-y Read lock byte.
-E <ext.fuse> Write extended fuse byte.
-F <fusebytes> Verify high/low fuse bytes. The LSB of fusebytes will be
compared to the low fuse byte, and the MSB will be compared
to the high fuse byte.
-L <lockbyte> Verify the lock byte.
-G <ext.fuse> Verify the extended fuse byte against the given value.
-O <address> Read oscillator calibration byte. Address is location of byte
as specified in the device's data sheet.
-S[f|e] <address>
Write oscillator calibration byte read with -O or -Z to given
location in FLASH (-Sf) or EEPROM (-Se).
-W Disable debugWIRE interface, enabling ISP mode. Only available
for debugWIRE devices.
-Y Perform the oscillator calibration sequence. See appnote
AVR053 for more information.
-Z <address> Load value from address in EEPROM prior to erasing the device.
This value can be written to FLASH or EEPROM again with
the -S[f|e] command.
Options:
-ae <start>,<end>
Specify address range for reading EEPROM memory. Default is
entire memory.
-af <start>,<end>
Specify address range for reading FLASH memory. Default is
entire memory.
-d <device> [required] Specify the type of device.
-ie <file> Specify input file for programming EEPROM memory.
-if <file> Specify input file for programming FLASH memory.
-m[i|j|p] Choose programming mode: ISP (-mi), parallel/high-voltage (-mp)
or JTAG (-mj) (default).
-oe <file> Specify output file for reading EEPROM memory.
-of <file> Specify output file for reading FLASH memory.
-z No progress indicator. Useful when redirecting output to file.
-D <devsbefore,devsafter,bitsbefore,bitsafter>
Set daisy chain settings. Only available in JTAG mode.
-I <speed> Specify ISP frequency (Hz). Only available for ISP mode.
-J <speed> Specify device speed (Hz). Only available for JTAG mode.
-R Apply external reset while programming. Only available in
JTAG mode.
Example usage: avrdragon.exe -d ATmega128 -e -pf -if c:\tmp\test.hex
Supported devices:
AT90CAN128, AT90CAN32, AT90CAN64, AT90USB1286, AT90USB1287,
AT90USB646, AT90USB647, ATmega128, ATmega1280, ATmega1281,
ATmega16, ATmega162, ATmega164P, ATmega165, ATmega165P,
ATmega169, ATmega169P, ATmega2560, ATmega2561, ATmega32,
ATmega324P, ATmega325, ATmega3250, ATmega3250P, ATmega325P,
ATmega329, ATmega3290, ATmega3290P, ATmega329P, ATmega406,
ATmega64, ATmega640, ATmega644, ATmega644P, ATmega645,
ATmega6450, ATmega649, ATmega6490
Supported devices for ISP, PARALELL/SERIAL HV mode and oscillator cal. only:
AT90PWM2, AT90PWM216, AT90PWM2B, AT90PWM3, AT90PWM316, AT90PWM3B,
AT90USB162, AT90USB82, ATmega168, ATmega168P, ATmega16HVA,
ATmega48, ATmega48P, ATmega88, ATmega88P, ATtiny13, ATtiny2313,
ATtiny24, ATtiny25, ATtiny261, ATtiny44, ATtiny45, ATtiny461,
ATtiny84, ATtiny85, ATtiny861
mfg
Gerold
:-)